Low-Profile Trolley Jack, 2 t, 95–510 mm Lift
Fits under lowered cars at 95 mm and lifts to 510 mm — heavy item, sea freight only.
Hand tools, torque wrenches, socket sets and garage equipment for home mechanics and small workshops
This is the family for people who work on their own cars, restore something older, or run a small workshop where the tools have to earn their keep. The selection follows one rule: CR-V or better steel, dimensions you can verify, and no tool that only looks professional. Torque wrenches are calibrated at the factory with a stated range and accuracy, socket sets state drive size and material, and magnetic rails state the pull strength per position so tools do not slide off when the van goes over a kerb.
What we deliberately do not sell: lithium-powered tools, because air freighting batteries into the lower 48 states means dangerous-goods documentation, a state-of-charge limit and carriers who may refuse the consignment at short notice. If you need cordless, buy it locally — that is the honest answer, and it is cheaper for you.
Heavy garage equipment is a different story. Trolley jacks and axle stands are excellent value in China but weigh 10–30 kg and can only travel by sea, which pushes the landed cost up and the delivery time out to weeks. Where that is the case, the product page says so and quotes the sea-freight timeline rather than pretending it is a two-day delivery.
Fits under lowered cars at 95 mm and lifts to 510 mm — heavy item, sea freight only.
Trim clips, retainers and ties, 400-piece set, sized by hole diameter and panel thickness.
Trim clips, retainers and ties, 180-piece set, sized by hole diameter and panel thickness.
Trim clips, retainers and ties, 200-piece set, sized by hole diameter and panel thickness.
Trim clips, retainers and ties, 300-piece set, sized by hole diameter and panel thickness.
Heat shrink tubing, 560-piece set, in 2:1 Ratio — for a crimped or soldered joint that has to survive vibration.
Heat shrink tubing, 200-piece set, in 3:1 Adhesive-Lined — for a crimped or soldered joint that has to survive vibration.
Heat shrink tubing, 150-piece set, in Transparent — for a crimped or soldered joint that has to survive vibration.
Abrasion-Resistant Cloth harness tape 19 mm wide and 25 m long — fleece, abrasion-resistant cloth or high-temperature.
Fleece harness tape 19 mm wide and 25 m long — fleece, abrasion-resistant cloth or high-temperature.
High-Temperature harness tape 19 mm wide and 15 m long — fleece, abrasion-resistant cloth or high-temperature.
Insulated terminals and the tool that closes them — 400 pieces, sized for 1.5 mm² and 2.5 mm² cable.
Insulated terminals and the tool that closes them — 300 pieces, sized for 1.5 mm² and 2.5 mm² cable.
Insulated terminals and the tool that closes them — 1200 pieces, sized for 1.5 mm² and 2.5 mm² cable.
Automotive cable, blade fuses and split conduit — the materials that finish a wiring job properly.
Automotive cable, blade fuses and split conduit — the materials that finish a wiring job properly.
Automotive cable, blade fuses and split conduit — the materials that finish a wiring job properly.
Battery tester for 6/12 V batteries: a carbon-pile load test or a conductance check with no drain.
Battery tester for 6/12 V batteries: a carbon-pile load test or a conductance check with no drain.
10 A charger and maintainer for 12 V and 24 V batteries, with float and repair modes and an US plug.
20 A charger and maintainer for 12 V and 24 V batteries, with float and repair modes and an US plug.
2 A charger and maintainer for 12 V and 24 V batteries, with float and repair modes and an US plug.
5 A charger and maintainer for 12 V and 24 V batteries, with float and repair modes and an US plug.
Workshop meter for 600 A: auto-ranging multimeter, clamp meter and insulation tester.
Workshop meter for 600 V CAT III: auto-ranging multimeter, clamp meter and insulation tester.
Workshop meter for 1 000 V: auto-ranging multimeter, clamp meter and insulation tester.
Lithium jump starter with a 12 000 mAh pack at 12 V, with or without a built-in tyre compressor.
Lithium jump starter with a 20 000 mAh pack at 12 V, with or without a built-in tyre compressor.
OBD2 scanner from basic fault-code reading to live data and multi-system ABS, airbag and transmission access.
OBD2 scanner from basic fault-code reading to live data and multi-system ABS, airbag and transmission access.
OBD2 scanner from basic fault-code reading to live data and multi-system ABS, airbag and transmission access.
2-channel handheld automotive scope with a 20 MHz bandwidth for signals a multimeter cannot show.
4-channel handheld automotive scope with a 50 MHz bandwidth for signals a multimeter cannot show.
A 6–24 V circuit tester for tracing feeds, earths and shorts — bulb, LED or powered probe.
A 12–24 V circuit tester for tracing feeds, earths and shorts — bulb, LED or powered probe.
A 6–24 V circuit tester for tracing feeds, earths and shorts — bulb, LED or powered probe.
A 20 cm magnetic tool strip in aluminium alloy with a anodised finish, holding up to 6 kg.
A 60 cm magnetic tool strip in aluminium alloy with a anodised finish, holding up to 15 kg.
24 pegboard hooks and holders in carbon steel with a zinc plated finish, for standard perforated board.
44 pegboard hooks and holders in carbon steel with a zinc plated finish, for standard perforated board.
60 pegboard hooks and holders in carbon steel with a zinc plated finish, for standard perforated board.
A 12-compartment parts organiser in polypropylene with a matte black finish and removable dividers.
A 24-compartment parts organiser in polypropylene with a matte black finish and removable dividers.
A 30-compartment parts organiser in polypropylene with a matte black finish and removable dividers.
Six 45 cm rails to get tools off the bench and onto the wall — 12 kg pull per rail, no drilling into the tool.
A 2-drawer tool cabinet, 560 mm wide and rated to 60 kg total, in carbon steel with a black powder coat finish.
A 4-drawer tool cabinet, 620 mm wide and rated to 100 kg total, in carbon steel with a black powder coat finish.
A 7-drawer tool cabinet, 680 mm wide and rated to 150 kg total, in carbon steel with a black powder coat finish.
A 8-drawer tool cabinet, 680 mm wide and rated to 180 kg total, in carbon steel with a black powder coat finish.
A 60 cm wall rack with 5 hooks in carbon steel with a black powder coat finish, for long-handled tools.
A 80 cm wall rack with 8 hooks in carbon steel with a black powder coat finish, for long-handled tools.
100 Mixed Workshop Selection bits in CR-V steel for impact drivers and bit holders, in a moulded bit case.
32 Slotted, Phillips & Torx bits in CR-V steel for impact drivers and bit holders, in a moulded bit case.
100 Security Bits bits in CR-V steel for impact drivers and bit holders, in a moulded bit case.
5 chisels and punches in carbon steel with a black oxide finish finish, in a roll-up tool roll.
11 chisels and punches in carbon steel with a black oxide finish finish, in a blow-moulded case.
6 chisels and punches in carbon steel with a black oxide finish finish, in a roll-up tool roll.
9 Ball-End hex keys in CR-V steel with a black oxide finish finish, held in a folding holder.
18 Long-Arm Metric hex keys in CR-V steel with a black oxide finish finish, held in a folding holder.
9 Metric hex keys in CR-V steel with a black oxide finish finish, held in a folding holder.
9 Torx hex keys in CR-V steel with a black oxide finish finish, held in a folding holder.
3 pliers in CR-V steel with hardened cutting edges and insulated grips, in a roll-up tool roll.
4 pliers in CR-V steel with hardened cutting edges and insulated grips, in a blow-moulded case.
5 pliers in CR-V steel with hardened cutting edges and insulated grips, in a blow-moulded case.
6 pliers in CR-V steel with hardened cutting edges and insulated grips, in a blow-moulded case.
File with a 5-blade pack, tensioning frame and a hardened aluminium alloy blade, in a canvas tool roll.
Saw and File with a 14-blade pack, tensioning frame and a hardened aluminium alloy blade, in a canvas tool roll.
Hacksaw with a 12-blade pack, tensioning frame and a hardened aluminium alloy blade, in a canvas tool roll.
12 screwdrivers in CR-V steel with magnetic tips and colour-coded handles, in a blow-moulded case.
24 screwdrivers in CR-V steel with magnetic tips and colour-coded handles, in a blow-moulded case.
44 screwdrivers in CR-V steel with magnetic tips and colour-coded handles, in a blow-moulded case.
6 screwdrivers in CR-V steel with magnetic tips and colour-coded handles, in a plastic rack.
A garage's first socket set: two drive sizes, metric and imperial, in a blow-moulded case that survives a van.
Ring and open-end spanners in chrome vanadium steel with a chrome plated finish, 12 sizes from 8–19 mm, supplied in a clip-in roll.
Ring and open-end spanners in chrome vanadium steel with a chrome plated finish, 14 sizes from 6–24 mm, supplied in a clip-in roll.
Ring and open-end spanners in chrome vanadium steel with a chrome plated finish, 25 sizes from 6–32 mm, supplied in a clip-in roll.
Ring and open-end spanners in chrome vanadium steel with a chrome plated finish, 32 sizes from 6–36 mm, supplied in a clip-in roll.
Ring and open-end spanners in chrome vanadium steel with a chrome plated finish, 8 sizes from 8–19 mm, supplied in a clip-in roll.
Ratcheting stands with a wide footprint for soft ground — 3 t per pair. Heavy item, sea freight only.
Wheel bolts, suspension, cylinder heads — with factory calibration certificate and ±3% accuracy.
Knife, Blades and Tape Measure with 3 pieces in zinc alloy, a lock-back handle and a matte black finish.
Utility Knife with 1 pieces in zinc alloy, a lock-back handle and a matte black finish.
Utility Knife and Blades with 10 pieces in zinc alloy, a lock-back handle and a matte black finish.
Cut-resistant gloves at A2/L2 Light-Duty, 1 pairs, with a coated palm for grip on oily components.
Cut-resistant gloves at Grip-Fit Mechanic's, 1 pairs, with a coated palm for grip on oily components.
Cut-resistant gloves at L5 Heavy-Duty, 1 pairs, with a coated palm for grip on oily components.
Ear Defenders at SNR 30 dB — ear defenders for on-and-off use, or a refill box of foam plugs.
Disposable Ear Plugs at SNR 35 dB — ear defenders for on-and-off use, or a refill box of foam plugs.
Impact-rated safety glasses, Clear Lens — specified by lens, because the one that fogs up comes off.
Impact-rated safety glasses, Anti-Fog Clear — specified by lens, because the one that fogs up comes off.
Impact-rated safety glasses, Over-Glasses — specified by lens, because the one that fogs up comes off.
Impact-rated safety glasses, Smoke Lens — specified by lens, because the one that fogs up comes off.
100 pcs nitrile gloves per box, Powder-Free — for oils, solvents and brake fluid where latex fails.
100 pcs nitrile gloves per box, Standard Blue — for oils, solvents and brake fluid where latex fails.
100 pcs nitrile gloves per box, Extra-Thick — for oils, solvents and brake fluid where latex fails.
Knee protection for long jobs at floor level — gel knee pads or a heavy-duty rolling kneeler.
Knee protection for long jobs at floor level — gel knee pads or a heavy-duty rolling kneeler.
Dust masks at the FFP2 level or a full-face shield — respiratory and face protection for dusty, splashy work.
Dust masks at the FFP2 level or a full-face shield — respiratory and face protection for dusty, splashy work.
A 250 mm mm adjustable wrench in carbon steel with a chrome plated finish and a Standard jaw.
A 300 mm mm adjustable wrench in carbon steel with a chrome plated finish and a Wide-Jaw jaw.
A 150 mm mm adjustable wrench in carbon steel with a chrome plated finish and a Standard jaw.
A 200 mm mm adjustable wrench in carbon steel with a chrome plated finish and a Standard jaw.
Impact sockets in CR-V steel with a black oxide finish finish for power tools, 10–24 mm.
Impact sockets in CR-V steel with a black oxide finish finish for power tools, 10–32 mm.
Impact sockets in CR-V steel with a black oxide finish finish for power tools, 19–50 mm.
Impact sockets in CR-V steel with a black oxide finish finish for power tools, 22–38 mm.
A Long-Reach Extendable ratchet in CR-V steel with a chrome plated finish and a quick-release 1/2 in square drive.
A Compact ratchet in CR-V steel with a chrome plated finish and a quick-release 1/4 in square drive.
A Standard ratchet in CR-V steel with a chrome plated finish and a quick-release 3/8 in square drive.
A 154-piece 1/2 in drive set in CR-V steel with a 90-tooth quick-release ratchet and 8–32 mm sockets.
A 24-piece 1/2 in drive set in CR-V steel with a 72-tooth quick-release ratchet and 10–32 mm sockets.
A 40-piece 1/2 in drive set in CR-V steel with a 90-tooth quick-release ratchet and 10–32 mm sockets.
A 46-piece 1/4 in drive set in CR-V steel with a 72-tooth ratchet and 4–14 mm sockets.
A 72-piece 3/8 in drive set in CR-V steel with a 72-tooth quick-release ratchet and 6–24 mm sockets.
A 90-piece 3/8 in drive set in CR-V steel with a 90-tooth quick-release ratchet and 6–24 mm sockets.
12 E-Torx External sockets in CR-V steel with a chrome plated finish for a 1/4 in drive.
12 Torx Internal sockets in CR-V steel with a chrome plated finish for a 3/8 in drive.
14 Star and Torx Mixed sockets in CR-V steel with a chrome plated finish for a 1/2 in drive.
A digital angle finder reading 0–360° in 0.1° steps, 200 mm long, in aluminium alloy.
A digital angle finder reading 0–360° in 0.1° steps, 300 mm long, in aluminium alloy.
A 150 mm digital calliper in stainless steel with a 0.01 mm resolution and a four-function LCD.
A 200 mm digital calliper in stainless steel with a 0.01 mm resolution and a four-function LCD.
A 300 mm digital calliper in stainless steel with a 0.01 mm resolution and a four-function LCD.
Feeler Gauge, 0.03–1.00 mm, 32 Blades in stainless steel, with 32 blades and a locking screw.
Thread Pitch Gauge Set, Metric and Imperial, 38 Blades in stainless steel, with 38 blades and a locking screw.
A self-levelling cross-line laser with a 15 m working range and ±0.3 mm/m accuracy, in ABS plastic.
A self-levelling cross-line laser with a 15 m working range and ±0.3 mm/m accuracy, in ABS plastic.
A 250 mm magnetic spirit level in aluminium alloy, accurate to ±0.5 mm/m, anodised.
A 600 mm magnetic spirit level in aluminium alloy, accurate to ±0.5 mm/m, anodised.
Stainless Steel Rule in stainless steel, 300 mm long, graduated to 1 mm.
Vernier Calliper in stainless steel, 150 mm long, graduated to 0.02 mm.
Analogue tread depth gauge in stainless steel, reading 0–25 mm, with a pocket clip.
Digital tread depth gauge in stainless steel, reading 0–25 mm, with a pocket clip.
Digital tyre pressure gauge reading 0–150 psi in ABS plastic, ±1% of full scale.
Dial tyre pressure gauge reading 0–60 psi in ABS plastic, ±2% of full scale.
3-in-1 Inflator tyre pressure gauge reading 0–220 psi in aluminium alloy, ±2% of full scale.
A chrome vanadium steel adaptor taking a 1/2 in drive to 3/4 in, black oxide finish, for using one torque wrench across two socket sizes.
A chrome vanadium steel adaptor taking a 3/4 in drive to 1/2 in, black oxide finish, for using one torque wrench across two socket sizes.
A 1/2 in drive torque wrench covering 20–210 Nm in chrome vanadium steel, ±3% accuracy, chrome plated.
A 1/2 in drive torque wrench covering 40–340 Nm in chrome vanadium steel, ±3% accuracy, chrome plated.
A 1/4 in drive torque wrench covering 5–25 Nm in chrome vanadium steel, ±4% accuracy, chrome plated.
A 3/4 in drive torque wrench covering 100–600 Nm in chrome vanadium steel, ±3% accuracy, chrome plated.
A 3/8 in drive torque wrench covering 20–110 Nm in chrome vanadium steel, ±4% accuracy, chrome plated.
A 1/2 in drive torque wrench covering 2–200 Nm in chrome vanadium steel, ±3% accuracy, chrome plated.
Adhesive Wheel Balance Weights, 10 g Strips, Pack of 12 in zinc alloy, for steel and alloy rims.
Adhesive Wheel Balance Weights, 5 g Strips, Pack of 12 in zinc alloy, for steel and alloy rims.
Wheel Balance Weight Assortment Box, 5 g and 10 g in zinc alloy, for steel and alloy rims.
Mushroom Plug Tyre Repair Kit, 15 Plugs, with the insertion tool and reamer included, for tubeless tyres.
Tubeless Tyre Repair Kit, 20 Rubber Strips, with the insertion tool and reamer included, for tubeless tyres.
Tyre Bead Spreader in chrome vanadium steel, black powder coat, for tubeless tyre fitting and removal.
Tyre Lever Set, 3 Pieces, 300 / 400 / 500 mm in chrome vanadium steel, black powder coat, for tubeless tyre fitting and removal.
Valve Stem Puller Tool, 4 Pieces in chrome vanadium steel, black powder coat, for tubeless tyre fitting and removal.
Tyre Valve Cores, Pack of 100, brass, for the tubeless valves on cars, vans and motorcycles.
Tyre Valve Caps, Pack of 50, ABS plastic, for the tubeless valves on cars, vans and motorcycles.
Valve Core Removal Tool, Four-Way, carbon steel, for the tubeless valves on cars, vans and motorcycles.
Bolt-In Metal Valve Stems, Pack of 2 in brass, for tubeless rims.
Snap-In Rubber Valve Stems, Pack of 4 in rubber, for tubeless rims.
Torque wrenches are supplied with a factory calibration certificate stating the range and accuracy. For professional use we recommend periodic recalibration; the product page states the accuracies claimed for each model.
Lithium batteries shipped by air into the lower 48 states require dangerous-goods documentation, a maximum state of charge and carrier acceptance that varies week to week. We avoid that risk entirely: cordless tools are better bought locally, and we would rather tell you than take your money and hope the consignment moves.
Yes, if they go by sea, and the product page says so plainly with the current transit estimate. Air freight on a 25 kg jack costs more than the jack, so we do not offer it as though it were free.